[efi]

Hello, I want to share with you the disappointment from my CX-30 (2.L, EXECUTIVE)

The car is nicely designed but annoys me the finish that Mazda made for the car.
All the plastic coverings in the wings on the front and back do not connect nicely to the vehicle's bumper, there is a protrusion.
The finish is simply poor and spoils the beautiful design Mazda has invested in the car,
Too bad.

 

[Polymetal Gray]

Hi, sorry to hear about your issue. No issues with mine, unfortunately yours might be a factory defect

 

[carbonized]

Have you raised your issue with the dealer yet? They can probably correct it.

 

[efi]

Hello again, from a check I did on other vehicles there is the same problem exists.
I would love to if you upload your picture, Can't believe there's no problem,
check again at all 4 points of the connections with the bumper.
Attaches a photo of another area in the vehicle.

 

[20CX30JBM]

I agree with @carbonized.

 

[t.mazda]

Hello, I want to share with you the disappointment from my CX-30 (2.L, EXECUTIVE) View attachment 410
The car is nicely designed but annoys me the finish that Mazda made for the car.
All the plastic coverings in the wings on the front and back do not connect nicely to the vehicle's bumper, there is a protrusion.
The finish is simply poor and spoils the beautiful design Mazda has invested in the car,
Too bad.

No problems with mine. Sounds like you should take your car back to the dealership to be inspected.

 

[dctokyo]

No problems with mine.

 

[steve67]

no problems with mine either....

 

[Jabo]

With mine they bend some hooks after placing a tow bar.
Now it is replaced under warranty.
The dealer has to make a warranty cleam.

[/QUOTE]

 

[20CX30JBM]

I took a close look at mine yesterday, there is a slight mismatch in the alignment of some of the cladding. I was a bit surprised how soft/flexible the lower couple of inches around the wheel openings.

 

[steve67]

I took a close look at mine yesterday, there is a slight mismatch in the alignment of some of the cladding. I was a bit surprised how soft/flexible the lower couple of inches around the wheel openings.

I did the same and have to agree, not the best quality . the front section froward of the bonnet/hood that wraps around to the lights was also very flexable.

 

[detailcarguy]

Hello, I want to share with you the disappointment from my CX-30 (2.L, EXECUTIVE) View attachment 410
The car is nicely designed but annoys me the finish that Mazda made for the car.
All the plastic coverings in the wings on the front and back do not connect nicely to the vehicle's bumper, there is a protrusion.
The finish is simply poor and spoils the beautiful design Mazda has invested in the car,
Too bad.

intresting as mine has the same slight issue on the passenger side of the bumper cover which i then went to my dealership and saw one on the show room floor with the same issue so i thought it was just how it was tho im curous to know the ones who dont have the same issue as to where they are made as mine is the same colour as yours and was manufactured in the Mexico plant.

 

[t.mazda]

All Canadian CX30 are from the Salamanca plant in Mexico. To verify your VIN will start with the number 3

 

[detailcarguy]

All Canadian CX30 are from the Salamanca plant in Mexico. To verify your VIN will start with the number 3

what i was asking is if other people say in the USA are having the slight issue or is it just related to canada with the manufacturing process in mexico and im not shooting down a county i had a 2012 Nissan sentra that was made in Mexico and it was a fantastic car.

 

[dctokyo]

what i was asking is if other people say in the USA are having the slight issue or is it just related to canada with the manufacturing process in mexico and im not shooting down a county i had a 2012 Nissan sentra that was made in Mexico and it was a fantastic car.

Mine was made in Mexico and I have not problem

 

[Salls]

No problem with mine. Made in Mexico

 

[detailcarguy]

when i buy my winter tires next week friday when im in my dealership im going to take a walk around the lot just to see how many like mine and others i can find lol just because im curious and i shall take pictures and ask the dealership about it.

 

[carbonized]

what i was asking is if other people say in the USA are having the slight issue or is it just related to canada with the manufacturing process in mexico and im not shooting down a county i had a 2012 Nissan sentra that was made in Mexico and it was a fantastic car.

Canadian and US versions are all made in Mexico, so you'd need to hear from owners in Europe/Asia for a comparison.

Mine seems mostly ok (US premium) from some angles the seam does look a bit off... but when I look closer it's ok. It's not as bad as what Efi is seeing though where it's definitely crooked. I think his is more of a real defect and should be corrected by the dealer.

 

[detailcarguy]

Canadian and US versions are all made in Mexico, so you'd need to hear from owners in Europe/Asia for a comparison.

Mine seems mostly ok (US premium) from some angles the seam does look a bit off... but when I look closer it's ok. It's not as bad as what Efi is seeing though where it's definitely crooked. I think his is more of a real defect and should be corrected by the dealer.

the only defect on mind is this one on the drivers side bumper cover and i noticed it 1 day after takeing delivery and i happned to stop into the dealer one day for a winter tire quote and one they had in the show room had the same sort of defect.. its just slightly no lined up.. i might bring this up to them since i leased mine and dont want the end of lease inspection company to think i hit something as i never have.

 

[pjbellemare]

Hello, I want to share with you the disappointment from my CX-30 (2.L, EXECUTIVE) View attachment 410
The car is nicely designed but annoys me the finish that Mazda made for the car.
All the plastic coverings in the wings on the front and back do not connect nicely to the vehicle's bumper, there is a protrusion.
The finish is simply poor and spoils the beautiful design Mazda has invested in the car,
Too bad.

Unfortunatly, you did not notice that at the delivery of the car. Now, good luck to have it fixed under warranty